Scanning large space - advice for using BLK360 with Pro 211886
Pages:
1
|
SpencerLasky private msg quote post Address this user | |
| Dan if this needs to be moved apologies upfront. This project I've asked about a few times - if I manage to make this work it should be a good reference for large domes, and mixed use cameras. This is a bank building with a 90' dome, two floors under it, two stairways up and down each and an outside space. Question - best pratice for doing BLK360 of the dome area and upper floor and seaming that to the M pro 2 of the smaller rooms, hallways, and floors below. The best research tells me I can get the dome on the BLK360 because matterport will not drop a hexagonal blur on it in the cloud software engine. This told to me by tech support, also confirmed by finding examples. Also, confirm all matterport pro 2 scans have the blur, it's not the camera data it's the software engine putting it on - of course, because the stitch will fail on full tilt-up with this camera, and unless you have a 90'dome directly overhead it's probably never been a problem. My pro 2 scan - top floor and lower floor (one more to go) https://my.matterport.com/show/?m=uoZqTEnesUy Note: the dome gets blurred on extreme tilt up. Today's Test - Theta V - it gave me the dome but can not navigate out of the small rooms, the capture fell apart pretty fast in this big space. https://my.matterport.com/show/?m=KkxRP8F8yLb Matterprot supplied a sample of BLK360 - however, it uses BLK360 outside only and switches to pro 2 at the entrance to cave - look up to see when the hexagonal blur start. Outside no blur as you approach door is the handoff, the resolution gets better too. https://my.matterport.com/show/?m=aRGwje8aXc3 Thank you for any help - I can not seem to get a matterport tech to save my life. Any ideas on that I'm all ears too. Spencer |
||
| Post 1 • IP flag post | ||
|
Garnetwest private msg quote post Address this user | |
| Is that Gotham Hall...the old Greenwich Savings Bank building? | ||
| Post 2 • IP flag post | ||
|
|
SpencerLasky private msg quote post Address this user | |
| No it's Williamsburg bank - there were two in Brooklyn this is the one in Williamsburg - both are amazing! Spencer |
||
| Post 3 • IP flag post | ||
|
|
Garnetwest private msg quote post Address this user | |
| Oh yes...i know that one as well. Amazing location. Good luck on the job!! | ||
| Post 4 • IP flag post | ||
Belfast, United Kingdom |
3dshowcaseuk private msg quote post Address this user | |
| I scanned these yesterday. Processed overnight. The perimeter of the warehouses were scanned with a pro 2 and the middle was approx 16 -20 spins of the BLK You can see which are which by the ceiling blur This was with HDR off and scan density medium Lots of good advice here. https://support.matterport.com/hc/en-us/articles/360000643507-Prepare-to-Scan-with-the-BLK360#blk360-setup-0-0 You will need extra batteries for BLK they run low very quickly[matterport]https://my.matterport.com/work/?m=mvAVXwzWX4k[/matterport] |
||
| Post 5 • IP flag post | ||
|
|
SpencerLasky private msg quote post Address this user | |
| Ok thanks 3DShowCaseUk - that is exactly what I needed to confirm though I have gathered as much on some of the sample videos that matterport has. My remaining question to fix this is, do I use my existing scan and add BLK360 for the center as you have done and then remove the older matterport pro 2 scan's from the center? This sequence makes sense to me so the model does not lose its information but the viewer can see the BLK and lookup - the problem for client solved. Or.. alternatively I can just hide these scans? Leaving the entire project intact for the new processing but then in workshop hide the m pro 2 scans so again the view gets to see the domes. | ||
| Post 6 • IP flag post | ||
Cincinnati, OH |
leonherbert private msg quote post Address this user | |
| @SpencerLasky I would just hide the pro 2 scans, can always use the better resolution for 2D photographs. | ||
| Post 7 • IP flag post | ||
|
Cincinnati, OH |
leonherbert private msg quote post Address this user | |
| @SpencerLasky Cool project | ||
| Post 8 • IP flag post | ||
Pages:
1This topic is archived. Start new topic?